Sub-Zero is the embodiment of style and also performance refrigeration. It isn’t just a device, your Sub-Zero is an essential element of your ideal cooking area. It makes good sense that you wouldn’t intend to trust your fridge to simply any kind of appliance repair business. You want a group of Sub-Zero fridge fixing specialists that can safeguard your investment while offering the premium solution you are worthy of.
It Is Fixed Device Repair work is the business you ought to rely on with all of your Sub-Zero repair service demands. Our technicians concentrate on Sub-Zero solution so you can rely on that we have the skills to finish the job right.
HOW TO USE THE ERROR CODE TROUBLESHOOTING GUIDE
Mistake Codes indicate issues registered by specific components. If mistake codes are signed up, they will certainly appear before temperature level analyses while in Diagnostic Setting.
NOTE: If Error Codes appear with a flashing “SOLUTION” annunciator before starting Diagnostic Mode, the device experienced too much compressor run condition that may or may not be connected with the Mistake Codes presented
To start Diagnostic Mode, press as well as hold either COLDER trick, after that press the POWER trick, after that release both tricks. Currently, inspect to see if Error Codes are present, making sure to toggle with all mistake and also temperature level readings by pushing either COLDER key or either WARMER secret. (See Mistake Code Table Below).
If Mistake Codes show up throughout Diagnostic Mode, follow the Mistake Code Troubleshooting Guide on the adhering to web page. The left column of the troubleshooting overview details the mistake codes. The information in the ideal column describes what tests to carry out and/or what action to require to fix the error.
NOTE: If error codes are observed in diagnostic mode, a non-flashing SOLUTION annunciator will appear on the LCD when Diagnostic Setting ends, suggesting mistake codes are still saved. Mistake Codes must be gotten rid of from the electronic control memory manually. To get rid of the non-flashing SERVICE annunciator and also the mistake codes, the problem has to be corrected and also the unit needs to get on, then:.
- On a model UC-24C: Press the Freezer WARMER as well as COLDER keys for fifteen (15) secs.
- On a version UC-24B, UC-24R, or UC-24RO: Press the Fridge WARMER and COLDER tricks for fifteen (15) secs.
Error Code Table
CODE | INDICATION |
05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
21 | Defrost overheat |
22 | No voltage feedback through Gray/White wire at defrost start |
23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
24 | Defrost under-heat |
30 | N/A |
40 | Excessive Freezer Compressor Run |
50 | Excessive Refrigerator Compressor Run |
Error Code | CAUSE | SOLUTION |
Error Code 11 | The refrigerator is too warm and/or the upper cabinet has been open too long | You will receive this error if your refrigerator’s upper cabinet has been open too long or if the upper cabinet is too warm. To resolve the error, disconnect the power from the unit at the circuit breaker. Leave the power off for at least one minute. Turn the power back on and keep the refrigerator door closed until the unit has reached optimal temperature. |
Error Code 05.
A. If “EE” for refrigerator compartment was presented and “SERVICE” blinking, inspect the following:.
- Thermistor electric links and also continuity from thermistor to J5 on control board. Reconnect/ repair service.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Replace if faulty. B. If “EE” for refrigerator compartment was NOT displayed, issue is periodic thermistor error:.
- Door not shutting properly. Correct door closing issue.
- Examine light button, electrical wiring & electric connections. Repair service electrical wiring/ links or replace switch.
- Check thermistor electrical links and also connection at J5 on control panel. Reconnect/ repair.
- Examine resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Replace if faulty.
C. If “EC 05” as well as “SOLUTION” were blinking before initiating diagnostic setting, unit likewise experienced too much compressor run problem that may or might not be associated with the “05” Error Code. See Error Code 50 Test/Actions.